VSI250755N Internal Gear Teeth Slewing Bearing are basic numbers only.
|
|---|
| No. | Brand | R | C | d | D | B | T | r | Noun |
| LM739749/LM739710 | NTN | - | 30,162 mm | 196,85 mm | 257,175 mm | 39,688 mm | 39,688 mm | - | - |
| LM739749/LM739710CD+LM739749XA | Timken | 3,5 mm | 66,675 mm | 196,85 mm | 257,175 mm | - | 85,725 mm | 0,8 mm | - |
| 4T-LM739749/LM739710 | NTN | - | 30,162 mm | 196,85 mm | 257,175 mm | 39,688 mm | 39,688 mm | - | - |
| LM739749-50000/LM739710-50000 | TIMKEN | - | - | 7.75 Inch | 196.85 Millimeter | 10.125 Inch | 257.175 Millimeter | - | - | - | Bearing |
| LM739710CD-2 | TIMKEN | - | - | 0 Inch | 0 Millimeter | 10.125 Inch | 257.175 Millimeter | 2.625 Inch | 66.675 Millimeter | - | - | Cup |
| LM739710CD-3 | TIMKEN | - | - | 0 Inch | 0 Millimeter | 10.125 Inch | 257.175 Millimeter | 2.625 Inch | 66.675 Millimeter | - | - | - |
| LM739710-2 | TIMKEN | - | - | 0 Inch | 0 Millimeter | 10.125 Inch | 257.175 Millimeter | 1.188 Inch | 30.175 Millimeter | - | - | Cup |
| LM739710-3 | TIMKEN | - | - | 0 Inch | 0 Millimeter | 10.125 Inch | 257.175 Millimeter | 1.188 Inch | 30.175 Millimeter | - | - | - |
| LM739710 | NTN | - | - | - | - | - | - | - | - |
| LM739710PX1 | NTN | - | - | 0 Inch | 0 Millimeter | 10.125 Inch | 257.175 Millimeter | 1.188 Inch | 30.175 Millimeter | - | - | - |
| LM739749-20024/LM739710-20024 | TIMKEN | - | - | - | - | - | - | - | - |
| Slew Drive For Solar Field SE7 | T:38.8 mm; DN:6.5 mm; L:95 mm; Db1:65 mm; R1:21 mm; s1:19.8 mm; Db2:71 mm; Thread grub screw G2:1/4-28 UNF; d:20.638 mm; J6:83 mm; A3:3.2 mm; GN:1/4-28 SAE-LT; Limiting speed:7000 r/min; Bearing:YAR 205-013-2F; A:30 mm; Fatigue load limit Pu:0.335 kN; Basic static load rating C0:7.8 kN; RG:1/4-28 UN |
| 310.16.0400.000&Type 16L/500 Slewing Ring | Material constant KM:330; l7 min.:55 mm; dk:60 mm; α:7 °; l3 min.:65 mm; d2 max.:104 mm; B:32 mm; Mass rod end:3.2 kg; Specific dynamic load factor K:100 N/mm²; h1:145 mm; l5 ≈:30 mm; d:45 mm; w:55 mm; d4 ≈:65 mm; Basic static load rating C0:224 kN; G:M 42x3; C1 max.:28 mm; Basi |
| 110.50.3550.12/03 Crossed Roller Slewing Bearing | P150°:77 kN; Pa:56 kN; H1:179.375 mm; L:628.65 mm; da:152.4 mm; R2:37.306 mm; Stabilizing ring:SR-34-0; Mass pillow block:132 kg; Eye bolt:2 x 3/8-16 UNC; Appropriate attachment bolt size G:1 in; h:54.769 mm; J1:107.95 mm; H:360.363 mm; Ca:119.812 mm; P120°:85.9 kN; N1:28.575 mm; P90°:14 |
| 310.16.0500.000 & Type 16L/650 Slewing Ring | Fillet Radius ra:1.50 mm; D:125.0000 mm; B:31.00 mm; Basic Dynamic Radial Load Rating C:44200 N; d:70.000 mm; Basic Static Radial Load Rating Co:17000 N; Grease Speed Rating n1:4800 rpm; Oil Speed Rating n2:5600 rpm; |
| 310.16.0600.000 & Type 16L/750 Slewing Ring | Fillet Radius ra:1.50 mm; Grease Speed Rating n1:6700 rpm; Grease Speed Rating Open/Shielded n1:6700 rpm; Oil Speed Rating n2:8000 rpm; Accessories:Two Shields; Sealed Speed Rating n3:4500 rpm; Basic Dynamic Radial Load Rating C:52700 N; Basic Static Radial Load Rating Co:31500 N; Oil Speed Rating O |
| 310.16.0800.000 & Type 16L/950 Slewing Ring | Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:11000 rpm; Basic Static Radial Load Rating Co:12700 N; Grease Speed Rating n1:11000 rpm; Basic Dynamic Radial Load Rating C:21600 N; B:22.20 mm; Accessories:No Shield, no Seal,; d:17.000 mm; D:47.0000 mm; Oil Speed Rating n2:14000 rpm; |
| 110.50.4000.12/03 Crossed Roller Slewing Bearing | r1 max.:0.6 mm; Lw:6.3 mm; Dw:2 mm; r1,2 min.:0.2 mm; r2 max.:0.8 mm; Mass needle roller:0.16 g; |
| 110.40.2800.12/03 Crossed Roller Slewing Bearing | D:190.0000 mm; Basic Dynamic Radial Load Rating C:157000 N; Basic Static Radial Load Rating Co:160000 N; Accessories:One Shield & Snap-Ri; Fillet Radius ra:2.50 mm; B:43.00 mm; d:90.000 mm; Oil Speed Rating Open/Shielded n2:3400 rpm; Grease Speed Rating Open/Shielded n1:2800 rpm; |
| 110.50.3150.12/03 Crossed Roller Slewing Bearing | Db max.:1197 mm; E:1165 mm; ra max.:5 mm; Basic dynamic load rating C:2920 kN; Da max.:1197 mm; das:1063 mm; Calculation factor e:0.2; Basic static load rating C0:7500 kN; d1 ≈:1073 mm; Calculation factor Y:0.6; Reference speed:160 r/min; D1 ≈:1148 mm; s max.:12 mm; Fatigue load limit Pu |
| Slew Drive For Solar Field ZE7 | T:42 mm; RG:1/4-28 UNF; L:79.4 mm; Hexagonal key size for grub screw N:3.175 mm; Housing material:Stainless steel; Housing:FYTWR 506 Y; d:31.75 mm; Recommended diameter for attachment bolts, mm G:10 mm; B:38.1 mm; Basic static load rating C0:11.2 kN; Basic dynamic load rating C:16.3 kN; H:141.3 mm; |
| 310.16.0700.000 & Type 16L/850 Slewing Ring | rc max.:0.6 mm; Calculation factor Y0:1.4; d:85 mm; Calculation factor Y1:1.5; Ca min.:6 mm; Calculation factor Y2:2.3; da max.:95 mm; K:4.5 mm; Limiting speed:4800 r/min; r3,4 min.:1.5 mm; Calculation factor e:0.44; Basic dynamic load rating C:293 kN; r5 min.:0.6 mm; T:58 mm; Reference speed:3200 r |
| Slew Drive For Solar Field ZE9 | Db:90 mm; B:42.9 mm; Basic static load rating C0:15.3 kN; Basic dynamic load rating C:21.6 kN; Mass bearing unit:0.72 kg; L:118 mm; Recommended diameter for attachment bolts, mm G:12 mm; Thread grub screw G2:5/16-24 UNF; T:46.4 mm; A1:17 mm; Fatigue load limit Pu:0.655 kN; Limiting speed:3200 r/min; |
| 110.50.4500.12/03 Crossed Roller Slewing Bearing | Calculation factor kr:0.03; Mass bearing:0.62 kg; Limiting speed:5000 r/min; r1,2 min.:1.5 mm; B:23 mm; da min.:49 mm; ra max.:1.5 mm; d:40 mm; Da max.:81 mm; Fatigue load limit Pu:1.02 kN; Basic static load rating C0:24 kN; da max.:52 mm; Basic dynamic load rating C:42.3 kN; d2 ≈:52.373 mm; C |
| Slew Drive For Solar Field PE7 | D:52.0000 mm; Grease Speed Rating n1:11000 rpm; d:20.000 mm; Basic Dynamic Radial Load Rating C:18600 N; Oil Speed Rating n2:16000 rpm; Fillet Radius ra:1.00 mm; Fillet Radius rb:0.60 mm; B:15.00 mm; Basic Static Radial Load Rating Co:9500 N; |
| 310.16.0300.000&Type 16L/400 Slewing Ring | H1:63.5 mm; J min.:165.1 mm; A2:101.6 mm; A1:60.325 mm; P90°:19.6 kN; h:30.956 mm; ba:24.606 mm; Cap bolt, SAE grade:8; Cap bolt recommended tightening torque:149.1 N·m; L:209.55 mm; Initial grease fill:65.205 g; Appropriate attachment bolt size G:0.5 in; db:49.212 mm; R2:15.875 mm; N1:15 |
| 310.16.0900.000 & Type 16L/1050 Slewing Ring | D:72.0000 mm; Fillet Radius ra:1.00 mm; Basic Dynamic Radial Load Rating C:29200 N; Basic Static Radial Load Rating Co:18600 N; Grease Speed Rating Open/Shielded n1:9000 rpm; B:19.00 mm; Accessories:Snap-Ring; Oil Speed Rating Open/Shielded n2:11000 rpm; d:20.000 mm; |